A Beginner's Guide to Installing a Bathtub
A Beginner's Guide to Installing a Bathtub
Blog Article
On this page below you can discover lots of awesome advice relating to How to Install a Bathtub: Install an Acrylic Tub and Tub Surround.
Installing a bathtub isn't specifically brain surgery, yet it does call for solid plumbing, woodworking, as well as sometimes, tiling skills. Replacing an old tub with a brand-new one is also a moderately difficult job. If the old bathtub is conveniently obtainable, the job can relocate easily; if you have to open up a wall surface to eliminate the old bathtub and also position the new bath tub, the job is a lot harder. In either instance, the project is within a house handyman's abilities, although you will need an assistant to leave the old bathtub and also embeded in the new one. Make certain you have qualified on your own for the job as well as are comfortable trying it. Instead of hiring a contractor to take control of a halfway-completed job, it is much better to think about utilizing one prior to you start. Possibilities are you might require a professional plumber to make tube connections.
This short article will assist you install a new bath tub in your washroom if you have already acquired a brand-new bathtub and also do not need to transform the arrangement of your previous supply of water pipelines.
Your tools and product list must make up the following:
Preparing for the Installation
First of all, the supporting structure provided with the bath needs to be fitted (if required) according to the supplier's instructions. Next off, fit the faucets or mixer to the tub. When suitable the tap block, it is important to see to it that if the faucet features a plastic washing machine, it is fitted in between the bathroom and the faucets. On a plastic bath, it is likewise sensible to fit a supporting plate under the faucets system to prevent strain on the tub.
Fit the flexible faucet adapters to the bottom of both faucets using 2 nuts and also olives (occasionally supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and after that pass the outlet through the hole in the bath. Make use of the nut supplied by the manufacturer to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next off, fit the end of the versatile overflow pipe to the overflow outlet. Afterwards, screw the pipe to the overflow face which need to be fitted inside the bathroom. Ensure you use all of the supplied washers.
Attach the trap to the bottom of the waste outlet on the bathtub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the catch to the electrical outlet. Link all-time low of the overflow tube in a comparable manner.The bathroom ought to now be ready to be fitted in its last setting.
Removing Old Taps
If you require to change old taps with new ones as a part of your installation, then the first thing you should do is detach the supply of water. After doing so, switch on the faucets to drain pipes any kind of water remaining in the system. The procedure of eliminating the existing taps can be fairly troublesome due to the limited gain access to that is commonly the situation.
Use a container wrench (crowsfoot spanner) or a tap device to undo the nut that connects the supply pipelines to the faucets. Have a cloth all set for the staying water that will certainly originate from the pipelines. When the supply pipelines have actually been removed, use the exact same device to loosen the nut that holds the faucets onto the bath/basin. You will require to stop the single faucets from turning throughout this process. When the taps have actually been eliminated, the holes in the bath/basin will need to be cleansed of any kind of old sealing substance.
Before carrying on to fit the brand-new faucets, compare the pipeline links on the old taps to the new taps. If the old faucets are longer than the brand-new taps, then a shank adapter is required for the new faucets to fit.
Installing the Tub
Utilizing the two wooden boards under its feet, put the bath tub in the needed setting. The wooden boards are helpful in equally spreading the weight of the tub over the location of the boards instead of focusing all the weight onto 4 little factors.
The next goal is to ensure that the bathtub is leveled all round. This can be accomplished by examining the level as well as changing the feet on the bathtub until the level reads degree.
To mount faucets, fit the bottom of the furthest versatile faucet port to the ideal supply pipeline by making a compression sign up with; then do the very same for the other tap.
Turn on the water and check all joints and new pipework for leakages and also tighten them if required. Load the bathtub as well as additionally inspect the overflow electrical outlet and also the normal electrical outlet for leaks.
Ultimately, repair the bath paneling as defined in the producer's instruction manual. Tiling and also securing around the tub needs to wait till the tub has been used at the very least once as this will certainly resolve it into its last setting.
Fitting New Touches
If the tails of the new faucets are plastic, then you will certainly need a plastic port to stop damage to the thread. One end of the adapter fits on the plastic tail of the tap as well as the various other end supplies a link to the existing supply pipelines.
If you require to fit a monobloc, after that you will call for decreasing couplers, which connects the 10mm pipeline of the monobloc to the conventional 15mm supply pipe.
Next, place the faucet in the installing hole in the bath/basin ensuring that the washers are in place between the faucet as well as the sink. Safeguard the tap in position with the maker offered backnut. As soon as the tap is securely in position, the supply pipelines can be linked to the tails of the taps. The faucets can either be attached by utilizing corrugated copper piping or with typical faucet connectors. The former type must be connected to the tap finishes initially, tightening just by hand. The supply pipelines can later be attached to the various other end. Tighten both ends with a spanner after both ends have been linked.
Tiling Around the Tub
In the area where the bath meets the ceramic tile, it is needed to seal the accompanies a silicone rubber caulking. This is important as the fitting can relocate enough to crack a rigid seal, causing the water to permeate the wall in between the bath and also the tiling, bring about complications with dampness and also possible leaks to the ceiling listed below.
You can choose from a variety of coloured sealants to blend in your components and also installations. They are marketed in tubes as well as cartridges, and are capable of sealing voids approximately a width of 3mm (1/8 inch). If you have a bigger void to fill up, you can load it with twists of soaked paper or soft rope. Keep in mind to always load the bath tub with water prior to sealing, to enable the movement experienced when the bathtub remains in use. The sealer can crack fairly very early if you do not consider this motion before securing.
Conversely, ceramic coving or quadrant floor tiles can be used to edge the bath or shower tray. Plastic strips of coving, which are easy to use and also reduce to dimension, are likewise easily readily available on the marketplace. It is a good idea to fit the floor tiles making use of waterproof or water-proof sticky as well as grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
I was made aware of that write-up about Installing A Bathtub through a good friend on another web page. Remember to take the opportunity to promote this write-up if you enjoyed reading it. Thank you so much for your time invested reading it.
Quick service, just dial! Report this page